07 saturn vue, remote start

Home / the12volt's Install Bay / Car Security and Convenience / 07 saturn vue, remote start (

Topic Closed)

Welcome Guest :)

Members

< Prev Page < Prev Topic Next Topic >

offroadzj

Gold - Posts: 2,043

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: June 03, 2005

Location: New York, United States

Posted: December 28, 2011 at 7:57 PM / IP Logged

is the yellow wire just simply connected to the passlock? Normally the passlock wire has to be cut with 2 wires connecting to each side. On mine I think it was WHITE/ red and WHITE/ black iirc.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

sigepkat1

Member - Posts: 9

Joined: December 27, 2011

Posted: December 28, 2011 at 9:41 PM / IP Logged

Yeah, it's just connected, not cut. Judging from the diagram (type 2), it's just supposed to be tapped. I see where on some of the other diagrams it's a cut and splice, but this one looks like it's just a tap.

offroadzj

Gold - Posts: 2,043

Joined: June 03, 2005

Location: New York, United States

Posted: December 29, 2011 at 6:36 AM / IP Logged

I believe you are correct, I was going off the cobalt I did.. my mistake.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: December 29, 2011 at 9:25 AM / IP Logged

i'm doing an 07 Vue this morning with the same module... i'll let you know if i run into any issues.....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: December 29, 2011 at 3:26 PM / IP Logged

what a PITA this thing was..... there is a "special" programming sequence that needs to be followed.... my LED went green on the module but it tripped the anti-theft tamper mode every time i tried to RS it.....

you may need to - select install type (1 or 2)... THEN get in it, close the door, start the vehicle, make sure the domelight is out, wait until all the warning lamps on the dash go out, AND THEN connect the pink ign wire on the idata to Ign..... this will allow it to learn properly....

they also tell me if you try to test it afterwards with the domelight on or with the door open it will go into "tamper mode"..... wth??

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

sigepkat1

Member - Posts: 9

Joined: December 27, 2011

Posted: December 30, 2011 at 10:05 PM / IP Logged

Tried your method Kevin, still just getting the red light...I've got a new module on the way, so I'll try that and see if anything happens. Will let you know.

sigepkat1

Member - Posts: 9

Joined: December 27, 2011

Posted: January 17, 2012 at 2:00 PM / IP Logged

Finally got a new module, installed it, it programmed, but it still won't start the damn car. Door locks work but when you hit the RS, the dash lights up, all of the RS wires send out the proper signals, but nothing happens. Does anyone know of a way to test the bypass to make sure it's bypassing?

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 17, 2012 at 4:06 PM / IP Logged

check the dash. If the security light flashes its still a bypass issue.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

sigepkat1

Member - Posts: 9

Joined: December 27, 2011

Posted: January 19, 2012 at 8:06 PM / IP Logged

This thing is about to get pushed out into traffic...When I hit the remote start on the clicker, the dash lights up like it does when I start it with the key. But it's still not turning over. The wires coming off the RS are lighting up like they should (ig., acc., etc.)...the module is "saying" it's programmed right. Ideas?

zerepdivad

Silver - Posts: 605

Joined: July 03, 2006

Location: Wisconsin, United States

Posted: January 20, 2012 at 7:47 PM / IP Logged

You really should be doing dei tech doc 1048 on these vehicles. I thought this was a pretty known issue. These along with equinox's, ions, and many others.

A DMM is a beautiful thing.

MECP Advanced Installer Certified.

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

07 saturn vue, remote start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.