the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Finding Multi-Outlet Distribution


Post ReplyPost New Topic
< Prev Topic Next Topic >
niteskyy 
Member - Posts: 9
Member spacespace
Joined: October 12, 2005
Location: United States
Posted: October 12, 2005 at 8:32 PM / IP Logged  

I was wondering where I can find a multi-port distribution block like the one shown on this website. http://www.electronixwarehouse.com/education/neon/installneon.htm I have been searching google but they are all for multiple amps and stuff like that.  I am wanting to put 4 neon lights in my car 1 under each seat and 1 under each side under the dash.  And the cords from the neon lights look like this http://www.oznium.com/cathode-kit

So if anyone knows where to get a distibution box that I am needing reply please aight thanks.

93cougarxr7se 
Member - Posts: 22
Member spacespace
Joined: February 09, 2004
Location: United States
Posted: October 15, 2005 at 1:50 AM / IP Logged  
That's just a simple positive and negative. Just wire them up that way. You could even hook them up to your cigarette lighter wires. Center is the positive, outside ring is the ground (negative). You can even take a couple wires to lengthen them if you need. If you have several lights and yours look exactly like that, wire all the red wires together, and all the black wires together, and use one switch.
The RED / yellow are just 12V positive. The black are 12V negative. You can get some wire at Wal-Mart for like $2.50 a spool and electrical tape for $.50 a roll and extend the wires. When you wire it in to an existing power source like the cigarette lighter, you would cut the insulation off of the positive, so you haven't cut the wire, and then separate the strands in half and put the new wire through the middle and twist it around the ligher wire securely and tape it. Do the same with the ground wire.
If you're not splicing, just connecting two loose ends, then put them in parallel with the ends that have 1/2" insulation cut off both pointing up, twist them together tightly. Pull the wires so they're pointing eachother, and twist the twisted end around the junction tightly so you can pull decently enough at the wires and they don't come apart. Then tape them up. If you need video to show this, I guess I can do that. But tomorrow I'm going to USACI/IASCA, maybe meet Alma Gates again. So it'll have to wait for Sunday.
But like I said, you don't need a distr. box, you just wire them together. A distribution box is just spending more money when you don't have to.
87 Astro 4.3L; Eclipse CD5000
88 Bronco 351W on 32x11.5x15 Yokohamas, Clarion Phaze 1 Components.
Home: MTX Thunder8000 in truck box & Parts Express amp.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer