Appropriate Wire Size

Home / the12volt's Install Bay / Car Audio / Appropriate Wire Size (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

jettagli03

Copper - Posts: 311

Joined: January 16, 2005

Location: United States

Posted: September 28, 2006 at 6:32 PM / IP Logged

I'm currently running 4awg wire to my two amplifiers, 60amps and 120amps each/180amps total.

I'm wondering after reading in the 'reccomended power and ground cable sizes' reading that 4awg is reccomended to 150amps where 2awg increases to 225amps.

Would it even be noticable by moving up to 2awg? Or even 0awg in the chance i upgrade both amplifiers in the future? (which will happen)

Even if it's not noticable, should I do it anyways?

shaggy12volt

Copper - Posts: 164

Joined: July 16, 2002

Location: Ohio, United States

Posted: September 28, 2006 at 6:50 PM / IP Logged

run you 2 4g wires or one 2g i use 0g most of the time for mutible amps

beter safe than soory later

The Shagmaster

1999 Chevy Suburban 15" lift sittn on 22's sets 7'5"

1992 Chevy Astro Van all Bagged out Dubbed THE SUICIDER

Installing for over 18 years Looking for empolyment NOW send PM for resum

josh1979

Silver - Posts: 320

Joined: July 03, 2006

Location: United States

Posted: September 28, 2006 at 6:50 PM / IP Logged

no such thing as too big and if you were going to upgrade amps why spend time and money changing the wire later. i would go with the largest wire you think you will ever need and can afford

bring back the rotary phone so i dont have to press 1 to proceed in english

jettagli03

Copper - Posts: 311

Joined: January 16, 2005

Location: United States

Posted: September 28, 2006 at 8:31 PM / IP Logged

That's what I figured. I was thinking about upgrading to 0awg and getting a little bit too much and upgrading my big three while im doing some wiring and getting an Optima battery too. I've looked into HO alternators for my car but since it's a Jetta it's not as cheap as I'd like, was quoted at $649 for a 170amp Appropriate Wire Size - Last Post -- posted image.

Appropriate Wire Size - Last Post -- posted image.

xtremej

Gold - Posts: 1,440

This member has made a donation to the12volt.com. Click here for more info.

Joined: February 24, 2006

Location: United States

Posted: September 29, 2006 at 12:06 PM / IP Logged

Have you checked with any local automtive elctrical shops in your area, I just had and alternator custom made for grand cherokee its only 300 for 200 amps.....Oh and bigger is always better on power/ground cables.

jettagli03

Copper - Posts: 311

Joined: January 16, 2005

Location: United States

Posted: September 29, 2006 at 7:52 PM / IP Logged

I really don't think there are any automotive electrical shops left in the area, atleast none I know about. I've known some but they go out of business. Anything I should look for in the yellow pages or something?

stevdart

Platinum - Posts: 5,816

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member consistently provides reliable information

Joined: January 24, 2004

Location: Pennsylvania, United States

Posted: September 29, 2006 at 9:54 PM / IP Logged

jettagli03 wrote:

I'm currently running 4awg wire to my two amplifiers, 60amps and 120amps each/180amps total.

I'm wondering after reading in the 'reccomended power and ground cable sizes' reading that 4awg is reccomended to 150amps where 2awg increases to 225amps.

Would it even be noticable by moving up to 2awg? Or even 0awg in the chance i upgrade both amplifiers in the future? (which will happen)

Even if it's not noticable, should I do it anyways?

The answer to this is: is the wire getting hot? Or even warm? If not, there is no reason to upgrade until such a time that you add more to the system.

The total fuse value of the amplifiers is not necessarily what amps they are pulling through the power wire.

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

silverado42000

Copper - Posts: 65

Joined: September 25, 2006

Location: United States

Posted: September 29, 2006 at 11:03 PM / IP Logged

i would go ahead and get the 2GAW just to be safe, or be like my friend who tried using too small a GAW and pulled up at a car show trying to show off with smoke coming out from under the hood, as for the alt, just go get you a nice high amp alt thats cheap and just make a custom bracket for it then the proper belt size, did it with a old car i used to have, squeazed a diesel alt in there, all the power i needed

Search for other posts by silverado42000

jettagli03

Copper - Posts: 311

Joined: January 16, 2005

Location: United States

Posted: September 30, 2006 at 12:11 AM / IP Logged

The wire is slighty warm but no where near hot, so I think I'm safe.

I'm thinking about still running an 8awg wire -- have PLENTY just sitting on my wire shelf -- along side the 4awg from the battery so each amp has their own wire and I can feel relaxed that I'm giving them what they need/want/can use.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Appropriate Wire Size

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.