the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2007 escalade alarm/ remote start wiring

Home / the12volt's Install Bay / Car Security and Convenience / 2007 escalade alarm/ remote start wiring (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: August 25, 2006 at 12:44 PM / IP Logged  
What a pain in the @$$ I remember when these rigs were SIMPLE.....
stitchme2gether 
Member - Posts: 5
Member spacespace
Joined: February 21, 2006
Location: United States
Posted: September 19, 2006 at 11:38 AM / IP Logged  
Okay, I just did a 07 Tahoe, and followed all DEIs tech tips and everything worked just fine, except for 2 things.  I had to modify the keysense wiring a little, and I can't get the rear liftgate to lock/unlock with aftermarket remote.  I would just run wires back there like I did the two front doors, but there's no motor back there.  It locks electronically, not with a motor.  Anyone with any tips on this?  Thanks in advance.
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: September 19, 2006 at 12:41 PM / IP Logged  

More info for comparison....

Wire/Function

 Colour Location/Description Polarity
PASSIVE ANTI-THEFTYESTRANSPONDER SEE NOTES
This vehicle is equipped with a TRANSPONDER passive anti-theft system. A bypass module may be available which will not require a key. Contact your supplier to find out. If one is not available to you, please see the appropriate security diagram before any remote start installation.
12 VOLTSRED / blackIn black plug on fusebox under dash +
IGNITIONPinkIgnition switch harness +
ACCESSORYBrownIgnition switch harness +
STARTERWhiteIgnition switch harness +
Start wire requires (+) through a 1280 ohm resistor.
KEY SENSEPinkIgnition switch harness +
TACH SIGNALSEE NOTE
Go to any coil on the side of the engine and use the wire that is not Pink, Black or Brown.
FUEL INJECTOROpposite from PinkAt any injector on engine AC
LOCKData module required
UNLOCKData module required
DOORPINGrayAt BCM on the left side of the steering column +
Located in the TAN connector.
TRUNK PINPink/blackAt BCM on the left side of the steering column -
Located in the PINK connector.
TRUNK RELEASEGrayAt BCM on the left side of the steering column -
Located in the PINK connector. The glass release wire is PINK and is found in the same connector.
FACTORY ARMData module required
FACTORY DISARMData module required
The OEM alarm will disarm automatically on remote start.
BRAKESWITCHBlue/whiteAt switch or BCM on left of steering column +
Located in the BROWN connector.
PARKLIGHTSLt.blueAt light switch or BCM on left of steering column -
Located in the TAN connector.
HAND BRAKELt.blueAt BCM on left of steering column -
Located in the BROWN connector.
HORNTanAt steering column or BCM -
Located in the BROWN connector. The BCM is located on the left side of the steering column.
VSS WIREYellow/blackIn Black connector on ECM AC
The ECM is located on the driver's side of the engine compartment behind the headlight.
boosting 6 
Member - Posts: 5
Member spacespace
Joined: January 31, 2006
Location: United States
Posted: November 07, 2006 at 4:08 PM / IP Logged  
how can i get the door locks to work properly? can someone help? i need to know what wires exactly to use. thanks in advance.
Mike M2 
Platinum - Posts: 2,652
Platinum spacespace
Joined: June 29, 2005
Location: United States
Posted: November 07, 2006 at 5:38 PM / IP Logged  
Power Lock see DirectFax document 1607    
Notes: To lock/unlock the driver door go to the driver door module or motor in the door and 5wi the tan (lock) and purple (unlock) motor wires.
To lock/unlock the passenger door go to the passenger door module or motor in the door and 5wi the tan (lock) and gray/black (unlock) motor wires.
To lock/unlock the rear doors use lt. blue (+) and white (-) at the BCM, gray plug, pins 7 and 9.
The BCM (Body Control Module) is to the left of the steering column.
Mike M2
Tech Manager
CS Dealer Services
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer