viper 5902 + dball in hyundai 2012

Home / the12volt's Install Bay / Car Security and Convenience / viper 5902 + dball in hyundai 2012 (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: March 02, 2013 at 1:55 PM / IP Logged

Look at menu 3 features 1 and 2.

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: March 02, 2013 at 1:56 PM / IP Logged

also on the reverse side of that large sheet, "learning the tach".

tameros

Copper - Posts: 75

Joined: November 26, 2011

Location: Egypt

Posted: March 02, 2013 at 2:06 PM / IP Logged

for menu 3 i set feature 1 to Option 2 (Automatic),

feature 2 to Option 4 (Tachometer)

But haven't made learning the tach, so i will go down now and test it

tameros

Copper - Posts: 75

Joined: November 26, 2011

Location: Egypt

Posted: March 02, 2013 at 2:34 PM / IP Logged

Remote start works but sometimes but one time it didn't want to work and showed on my alarm remote the figure of brake pedal and red around it then says brake on

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: March 02, 2013 at 2:49 PM / IP Logged

If that keeps happening you might have to hardwire the brake input to the brake switch.

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: March 02, 2013 at 2:54 PM / IP Logged

Brake shut down input going to DB-ALL red plug, pin 6 Grey.

Cut and join to wire going to rear that goes POS when brakes are applied, also at brake switch.

But before that, with ignition on, test with DMM to see if there's any voltage on that line, say 3-5 volts without the brake being depressed, sometimes happens with LED lights.

tameros

Copper - Posts: 75

Joined: November 26, 2011

Location: Egypt

Posted: March 02, 2013 at 3:06 PM / IP Logged

OK i will test if that line has 3-5 volts when ignition is on and brakes not depressed, and also i will monitor a couples of days if it happens again, before i cut.

You mean if i cut i join to the wire going to the switch behind the brake pedal, right?

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: March 02, 2013 at 5:44 PM / IP Logged

Yes, the wire from the R/S marked (+) brake shut down input, connect that to the switched brake wire. It would previously have gone to the grey on the red plug, pin 6.

tameros

Copper - Posts: 75

Joined: November 26, 2011

Location: Egypt

Posted: March 05, 2013 at 10:22 AM / IP Logged

this is the brake schematic

viper 5902 + dball in hyundai 2012 - Page 7 -- posted image.

tameros

Copper - Posts: 75

Joined: November 26, 2011

Location: Egypt

Posted: March 05, 2013 at 10:36 AM / IP Logged

this is the stop lamp and brake switch schematic

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.